UBNT

From My Notepad
Jump to: navigation, search

Signal Strength via SNMP

snmpwalk -c community -v1 accesspointip .1.3.6.1.4.1.14988.1.1.1.2.1.3

Aircam Gen 1

VLC Endpoints

Alternatively, point VLC or your preferred RTSP h.264 viewer at 
1280X720 -- rtsp://camera-ip-address:554/live/ch00_0
640X480 -- rtsp://camera-ip-address:554/live/ch01_0
320X240 -- rtsp://camera-ip-address:554/live/ch02_0
160X112 -- rtsp://camera-ip-address:554/live/ch03_0

Console configuration options

Source


echo 1 > /proc/isp0/ae/ev_mode

echo "w brightness 0" > /proc/isp0/command
echo "w contrast 0" > /proc/isp0/command
echo "w saturation 0" > /proc/isp0/command
echo "w sharpness 0" > /proc/isp0/command

echo "w denoise 0" > /proc/isp0/command
echo "w dpc 0" > /proc/isp0/command

echo "w crosstalk 0" > /proc/isp0/command
echo "w crosstalk 100" > /proc/isp0/command

echo "w gamma 4" > /proc/isp0/command

Properties:

 r brightness - Get current brightness
 w brightness VALUE      - Set brightness as VALUE, 0~100
 r contrast              - Get current contrast
 w contrast VALUE        - Set contrast as VALUE, 0~100
 r hue                   - Get current hue
 w hue VALUE             - Set hue as VALUE, 0~100
 r saturation            - Get current saturation
 w saturation VALUE      - Set saturation as VALUE, 0~100
 r gamma                 - Get current gamma setting
 w gamma VALUE           - Set gamma as VALUE
 r dpc                   - Get current defect pixel correction level
 w dpc VALUE             - Set defect pixel correction level as VALUE, 0~100
 r crosstalk             - Get current crosstalk reduction level
 w crosstalk VALUE       - Set defect crosstalk reduction level as VALUE, 0~100
 r denoise               - Get current noise reduction level
 w denoise VALUE         - Set noise reduction level as VALUE, 0~100
 r sharpness             - Get current sharpness level
 w sharpness VALUE       - Set sharpness level as VALUE, 0~100
 r auto_adj_en           - Get enable/disable status of auto adjustment function
 w auto_adj_en VALUE     - Enable or disable auto adjustment function VALUE
 r auto_cs_en            - Get enable/disable status of auto chroma suppression
 w auto_cs_en VALUE      - Enable or disable auto chroma suppression VALUE
 r auto_cs_th            - Get auto chroma suppression threshold
 w auto_cs_th VALUE      - Set auto chroma suppression threshold as VALUE
 r auto_cs_gain          - Get chroma suppression ratio
 w auto_cs_gain VALUE    - Set chroma suppression ratio as VALUE
 r sen_exp               - Get current sensor exposure time in us
 w sen_exp VALUE         - Set sensor exposure time as VALUE in us
 r sen_gain              - Get current sensor gain (2¡¦s complement fixed point Format:10)
 w sen_gain VALUE        - Set sensor gain as VALUE (2¡¦s complement fixed point Format:10)
 r mirror                - Get enable/disable status of sensor mirror function
 w mirror VALUE          - Enable or disable sensor mirror function VALUE
 r flip                  - Get enable/disable status of sensor flip function
 w flip VALUE            - Enable or disable sensor flip function VALUE
 r ae_en                 - Get enable/disable status of ISP AE
 w ae_en VALUE           - Enable or disable ISP AE function VALUE
 r awb_en                - Get enable/disable status of ISP AWB
 w awb_en VALUE          - Enable or disable ISP AWB function VALUE
 r af_en                 - Get enable/disable status of ISP AF
 w af_en VALUE           - Enable or disable ISP AF function VALUE
 r md_en                 - Get enable/disable status of ISP MD
 w md_en VALUE           - Enable or disable ISP MD function VALUE
 r knee_en               - Get enable/disable status of ISP Knee function
 w knee_en VALUE         - Enable or disable ISP Knee function VALUE
 r knee_point_x          - Get X value of knee poin
 w knee_point_x VALUE    - Set X value of knee point as VALUE, 0~4095
 r knee_point_y          - Get Y value of knee point
 w knee_point_y VALUE    - Set Y value of knee point as VALUE, 0~1023
 r shdc_ref              - Show SHDC informations
 w reload_cfg [PATHNAME] - Reload cfg file
 r reg ADDR [COUNT]      - Read ISP registers ADDR
 w reg ADDR VALUE        - Set ISP register ADDR as VALUE
 r sen_reg ADDR          - Read sensor register ADDR
 w sen_reg ADDR VALUE    - Set sensor register ADDR as VALUE
 w grab [PATHNAME]       - Grab one frame and save as PATHNAME